sistermosque31

Dual Fuel Range Cooker With 13amp Plug Are you a home cook who loves the responsiveness of gas cooktops, but requires an oven to bake in? Discover a dual-fuel range cooker that offers the best of both worlds. Gas cooktops are favored by many home chefs who have years of experience in the kitchen because of their superior temperature control. They also allow them to utilize advanced cooking techniques, such as charcoaling. These powerhouse stoves can be expensive, particularly when you need an additional gas connection and electrician for installation. What is a 13amp plug? If you have a dual fuel range cooker (also called an electric and gas oven) is required, you'll need an appropriate 13 amp plug. The plug must also be hard-wired by a licensed electrician into the cooker ring. This ensures the current flowing through the plug does not exceed the limit of safety which could cause an electrical fire. graded dual fuel range cookers is equipped with an electric fuse that regulates the current. The fuse explodes when the current flows through it over its capacity, which safeguards the appliance from an overload of electricity. The fuse is listed at 13 amps as shown on the top of the plug and it indicates the maximum current that the plug can pass without causing harm to the appliance or overheating the socket. When replacing fuses, it's important to use the same amperage rating as the original. If you replace the fuse with one of an alternative rating, you risk overheating the socket and placing yourself and others at serious risk. A 13 amp fuse is likely to be a ceramic type, which is very robust and able to withstand the high temperatures produced by the range cooker. Ceramic elements are also fire-resistant and therefore a better choice than other kinds. There are many ways to install the 13 amp plug. The plug can be connected to a live socket by using screws or a plastic jaw cord clamp. The cord clamp should be tightened after the plug is tightly pushed into place. Before connecting the wires you might need to take off the cardboard wiring diagram that is positioned on top of the pins on some plugs. It is crucial that the wires are cut to the right length, as cutting them too long could result in them becoming crushed when the plug cover is replaced. The earth wire should be the longest to connect it before the neutral and line pins. How do reconditioned dual fuel range cookers connect the 13amp plug? The majority of dual fuel range cookers sold in the UK are wired to a 13 amp plug socket and this is crucial as ovens can draw a significant amount of current and standard plug sockets are capable of 10 amps. In general, new appliances should be fitted with a plug at the point-of-sale. This is to ensure compliance with the Plugs and Sockets etc. (Safety Regulations) 1994. However, older appliances may not be connected to the plug, and this is where the issue arises. The first step to take when connecting a cooker to an existing plug socket is to make sure that the rating of the fuse in the fuse box is in line with the rating of the plug. This is crucial because a fuse that is not properly sized could pose a risk. It is also recommended that the fuse has been fully seated in the cartridge, and there isn't any movement. Next up is to prepare the flex that is to be used. Remove the sheathing to reveal the three conductors that are insulated. Utilize a utility knife to cut the sheathing beyond the grip of the cord at the point of entry into the plug. This won't be able to penetrate the insulated conductors. The nick should be wide enough to allow for the cable and sheathing to separate when the sheathing is pulled back. Cut off the excess sheathing leaving about 40mm beyond the flex. This flex is placed over the plug with the earth terminal at the top and the neutral and live terminals at the bottom. The sheathing on each pin is removed using coloured conductors as a guide. The internal cable is then inserted to the terminal using the cord grip. If the plug has a clamp for cords that is screw-type, let it loosen and then pull the insulation back to reveal the copper wires. Connect each wire insulated to the correct terminal using the channel in the plug. Start with the earth conductor, then the neutral, and finally, the live. What is the maximum draw of a 13amp plug? The maximum current draw of an 13amp plug is 3kw at 230 volts. This is a significant amount of power but the standard fuse on a UK plug won't fail until the cable reaches a dangerous temperature. A defective plug or socket could cause fire, so it's important to be aware of how much you are using, especially in the kitchen. The fuses in plugtops are ceramic, around 25mm in length and 240V mains rated. They will feature the BS kitemark or similar mark on the side, and they contain sand. Plastic or glass alternatives are available, but should not be used in conjunction with a live plug. In the UK the majority of dual fuel range cookers are hardwired. They are not able to plug directly into an outlet on the wall. They are usually connected to a dedicated cooker ring circuit that is suitable for appliances that draw up to 20 amps. You can test the ring circuit of your home by examining the fuse box or by asking an electrician in your area. They should be able to tell you if the sockets within your home are connected to the same ring or separate and if there is a dedicated circuit for your oven. The size of your kitchen is one of the main factors when you decide to buy a dual fuel range cooker. We offer a variety of cookers that will fit any space. Choose from compact 50-60cm dual fuel models or huge 90cm+ double oven options from leading brands like Rangemaster and StovesAreUs. We also offer a wide range of multifunction electric and gas cookers. These multi-functional appliances let you cook a variety of dishes such as curries, casseroles, and pasta! Explore our full range of Cookers in Currys online or head in-store for a look. We offer free home installation and delivery on selected range cookers, as well as flexible payment options. Our staff is ready to answer any questions you may have. Contact us via email or by phone. Credit is subject to status, and terms and conditions apply. What is the maximum current draw of a cooker switch? There is lots of confusion regarding what the maximum current draw of a cooker switch actually is. The majority of cookers are hard-wired and connected to an oven-ring circuit and not a standard socket. This is due to the fact that they typically consume more than 20 amps of power each time the gas and electric ovens are used. Therefore, you cannot find a dual range cooker with a fuel source that can be connected to a standard socket, as it could pose a significant fire risk and be against electrical safety regulations. An experienced electrician will install any new electrics to an appliance in the kitchen and will make sure that the total load (both the hob and oven) do not exceed the power capacity of the circuit. Dual fuel range cookers blend the responsiveness of a gas stove with the precision and precision of an electric oven. This is why they are highly sought-after by cooks and chefs alike. Dual fuel range cookers are perfect for trying out different cooking techniques, like searing or grilling. When purchasing a new range cooker you'll need to take into consideration several factors like size, performance and price. It is also necessary to have a gas connection in your home for the appliance. If you're unsure, it's best to have an Gas Safe engineer inspect your property prior to installation. Currys' dual fuel range cookers come in a variety of models to meet all budgets. From affordable models by Indesit and Zanussi to our own Essentials collection. If you're seeking something more sophisticated we have a selection of premium JennAir models, which feature many innovative features. When purchasing a new dual fuel range cooker, it's important to check the manual of the owner for specific details on the electrical and gas requirements. You will need to ensure that your home has a gas hook-up that is suitable, and you may need to get a plumber to install it for you if necessary. It is also possible to require a dedicated cooker-ring circuit, installed by an experienced electrical engineer.